1:28
I've been running this cell into the ground for the past week and I've found the sweet spot to be at around 10 Amps. The configuration of this cell is: (17 Plates) -nnn+nnn-nnn+nnn-
  • 15 Oct 2010
  • 2 723
Share Video

1:27
This is a video showing my HHO Gas Filter that is a variation of jdcmusicman's design. It is intended to remove any impurities from the exhausted gas of HHO fuel cells. All of the parts were very inexpensive and can be purchased from just about any home improvement store.
  • 12 Oct 2010
  • 943
Share Video

1:56
This is a new design that I threw together to see if it would work. It is a smaller fuel cell, but the output is good and amperage is very low.
  • 9 Oct 2010
  • 523
Share Video

4:30
This is a video that I put together to show a concept for a fuel cell, bubbler, and reservoir all in one design.
  • 10 Mar 2009
  • 407
Share Video

6:35
This is a video on how to build the "Smallest DryCell on the Internet"
  • 10 Mar 2009
  • 326
Share Video

4:11
This is an updated version of the Washer Cell that I was experimenting with. I've already come up with a DryCell version of this, so this will be the last video of the Wet Cell version.
  • 13 Jul 2011
  • 481
Share Video

2:59
I had a ton of spare SS Washers laying around, so I wanted to see if I could turn them into a fuel cell. I guess it worked, because if it didn't I wouldn't be posting this video.
  • 10 Jul 2011
  • 1 019
Share Video

2:37
This video is for all of the skeptics out there that don't believe my design is producing HHO! I am not using a water pump, an air compressor or any trick to get these results. I'm not hiding anything and I don't need to!
  • 12 Mar 2009
  • 1 409
Share Video

2:07
Here is a quick video of my ultra small Dry Cell.
  • 13 Sep 2009
  • 566
Share Video

3:48
Here is a Single cup HHO Fuel Cell that I threw together, just to see if it could be done. It took a little bit of time to come up with a working design, but so far it is looking promising!
  • 10 Mar 2009
  • 446
Share Video

0:58
Since I finally got my amp meter, I figured I should put a video together to show the actual amperage the FlipCup Fuel Cell draws. 12 Volts 6 Amps 1/2 teaspoon of KOH (Potassium Hydroxide) No PWM (yet)
  • 23 Sep 2009
  • 268
Share Video

4:11
I finally worked out all the bugs in my FlipCup Dry Cell. It only took 2 months of troubleshooting and redesigning, but in the end... It was definitely worth the wait! Configuration is + NN NN NN NN NN - (stacked neutrals)
  • 1 May 2009
  • 1 981
Share Video

1:26
I tightened the spacing on the 12 cup "Flip Cup" cell to enable the current to pass from one cup to another more easily. This demonstration is at 12 Volts, Under 15 Amps, and a 1/2 teaspoon of KOH. The container and connections don't get hot!!!
  • 10 Mar 2009
  • 309
Share Video

1:53
Here is my redesigned Flip Cup Fuel Cell. The new configuration is (from bottom to top) Negative Neutral (2 cups stacked) Neutral (2 cups stacked) Neutral (2 cups stacked) Neutral (2 cups stacked) Neutral (2 cups stacked) Positive
  • 13 Oct 2011
  • 439
Share Video

8:57
This video was put together to help others learn how to build a HHO Fuel Cell. This walkthrough will show you how to build my personal HHO Fuel Cell Design. The name of the design is "Flip Cup" Fuel Cell. My design is free to the public. Enjoy
  • 23 May 2009
  • 3 403
Share Video

1:24
Here's a quick video to show off my PoBoy HHO Output Test Enclosure. Test Results will be here soon!!!
  • 11 Jun 2009
  • 524
Share Video

3:44
Here is a small video describing how my cell is put together.
  • 24 Sep 2009
  • 1 055
Share Video