This guy can throw like Bruce Lee, he used few chopsticks to make holes through a steel utensil. He threw them and they went right through.
The single bird should be very scared to see humans p**ping through the vent hole. But shockingly, the opposite reaction took place.
Vapor (or vapour) recovery is the process of recovering the vapors of gasoline or other fuels, so that they do not escape into the atmosphere. This is often done (or required by law) at filling stations, in order to reduce noxious and potentially explosive fumes and pollution.
The negative pressure created in the (underground) tank by the withdrawal is usually used to pull in the vapors. They are drawn-in through holes in the side of the nozzle and travel through special hoses which have a return path.
three wld, naughty & horny pornstars are fucked by Johhny Sins.
They blow his cock, then Johhny lick their asses's holes and pussies finally he puts his big dick in their pussies and asses, in then he cums in a pornstar mouth and she swaps his cum between their mouths
You’ve never seen insane if you haven’t seen this video! This drill, supposedly made with Vibranium, drills a clean hole through a Nokia mobile phone. If that wasn’t crazy enough, the phone still rings with two holes through it!
Perforated Media Explained
It’s time to make an impression with Perforated Media.
ViewThru also known as Perforated is a special type of vinyl that has tons of holes in it. They are most recommended for store fronts, glass front office buildings and rear window of vehicles.
Basically, used on windows, the outside can be printed on, while the dark adhesive inside allows users to see out. Even then the ViewThru material allows high impact prints on the outside. Additionally, perforated media can also reduce the impact of sun that can enter, keeping the space cooler.
• Helps maintain privacy, as you can see outside but a person outside just gets a view of the image and has no access to see the inside.
• It is great for cutting sunlight and reducing heat
• Allows for full-digital prints
• Provides a clean, uniform look over entire window
For any perforated media requirements, you can visit us."
Making hommade substrate for mycology use
-1 cup measuring
-Vermiculite sold at Home Depot, Lowes, Walmart and Target
-Brown rice flour sold at Walmart and major grocery stores
-Foil 3"x 3"
-Wide Mouth mason w/lids jars any size as long as it is not regular style jars
-Large soup pot or Pressure cooker
-Steamer for bottom of pot
-Small nail or 1/8" drill bit
-Hammer if using no drill bit
-Distilled or Spring Water
First use a 1/8th drill bit or nail to poke or drill 4 holes on lid In this video I used 5 holes do not do that because it might dry out the water content in jars which stalls the colonizing of the mycelium. Boil jars and lids with band in water for 20 minutes than take out and set them upside down on a paper towel. Wipe off excess moisture from bands and lids.
Prepare your substrate by putting 2 cups of vermiculite, 1 cup brown rice flour, and 1 cup distilled or spring water (2 parts Vermiculite,1 part brown rice flour, 1 part water. You can make as much as you want as long as you follow the
2x1x1 part mixture. Mix Vermiculite and flour together first until well mixed with fork than slowly add water until consistancy is like damp sand. Fill jars with spoon very lightly without compacting substrate should be loose and airey, leave a 1/2" space from top of jar. Wipe down rim of jar with paper towel so no moisture is left, if you fail to do this the risk of contamination is can happen. Put a dry layer of only vermiculite on top of the damp substrate until it is flush with rim of jar. Wipe rim again to clean any dust off. Put lids on jars tight and cover them with foil. The purpose of the foil is to prevent water from dripping through the holes on the lid and ruining the moisture content. Too much moisture can cause mycelium to not grow. Too little can make substrate too dry which will cause no growth
Video 6: Midwest Grow Kits Review
I do not recommend using a closet to colonize do to lack of (FAE) Fresh Air Exchange.
Instaed put jars in cupboard over fridge or on a shelf were they can get indirect light/sun light which means that the light shines from the outside but not on the jars.
Do not leave the foil on the jars do to lack gas exchange which will suffecate you mycelium
You can put medical tape over the holes which is optional
Keep temerature at 78 - 82 degrees F . Monitor jars by turning slowly to check for green,purple,yellow or black. Any color other than white will be contaminates. Do Not open jars or the spores will spread and stick to everything ruining
future grow. Instead take closed jars outside and put in garbage. You can put unopen jars in boiling water for 45 minutes than dump conentents outside and than boil empty jar agin for 45 minutes. This is not recommended
and is only done if you don't want to buy new jars. Leave on shelf for 2 weeks or until jars are fully white. Than alow the substrate to sit a full week for mycelium to grab a hold of substrate. After 7 days of sitting after fully colonized prepare for The dunk and roll method and
prepare your fruiting chamber.
The method of useing two totes with the bottom tote filled 2/3 full and putting a submergable aquarium heater w/thermostat inside the water than useing 2nd tote placed on the water than
adjusting heater untill proper temp. is reached. Using a small led light on lid / sides or indirect sunlight 24 hours a day until fully colonized This method is not recommended by me but it works for other people.
The Problem I experienced using this method is the jars will slide and there is very little FAE "fresh air exchange and very little gas exchange. Midwest grow kits recommend this way but they are totally wrong and I would not consider anything they say.
I bought the ultyamite kit for 100 dollars and never used it because I found that it was an improper way to colonize and/or fruit
The use of a shotgun fruiting chamber is the easiest way to grow mushrooms. It was designed to allow adequate air flow and high humidity by the use of perlite to hold water. The holes that are drilled create air flow that enters from all sides. By using a storage bin and drilling 1/4 inch holes on all sides and placing perlite on the bottom maintains the 3 key factors in the growth process of the mushrooms, which are "FAE" Fresh Air Exchange, "RH" Relative Humidity, and Temperature. You can use any small LED light but a 6500 kelvin/100 watt CFL is the best for optimal growth. Make sure to elevate the terrarium 2" or above.
This video explains How To Make A Shotgun Chamber For Fruiting Mushrooms. Get a clear plastic storage bin and mark a dot 2" apart from top to bottom all the way around the bin. Mark all 6 sides than use a 1/4" drill bit to holes in the marked spots. Be careful not to crack the plastic. Clean the burrs with a razor blade than add perlite 4" in depth. Attach a light and place in a room that can keep the temperature and humidity steady. Put your fully colonized trays or cakes inside on top of a piece of foil. Mist an fan to promote pinning.
The purpose of a still air box is to prevent air flow that mold spore use to move through the air. This box keeps the air from moving and allows for inoculation of prints or spore syringes. Using a clear plastic storage bin cut two 4" holes on one side so your arms can reach inside. Make sure to sanitize with 70% alcohol.
The most amazing hole in one you will ever see.