My All New Newman Motor 2 Running It Up.

Ok let's just say you are correct and lets leave it there.

no i fail to get the picture, I'm sorry but its imposable to get overunity by converting electricity to magnetic flux (heat losses) then magnetic flux to kinetic energy via magnetic repulsion (waisted flux as it goes outside the coil as well as inside) and then store that for a short time (friction losses) and then hope to GAIN energy by running the conversions the other way round.. it just has me dumbfounded that anyone would think this would work!!!

Probably bad examples but I think we all get the picture.

and yet no one is using them to power there house or lab.. in fact i would like to see one power a single LED for more than a few minutes (giving time for the power to run out), if overunity exists then it would change the laws of conservation of energy and make allot of the rules of physics wrong, you cant get power from nothing and i REAL fail how you can get it from an inefficient design alternator.. just using the laws of electro-magnetics and generation you know that it cant happen

i don't know where you get the idea that the microwave, the computer, the Internet or the jet wouldn't work... they all worked from the get go just not very well, and people never thought they would be as commonly used as they have become.. but all there effects could be PROVED i have yet to find ANY solid evidence that this "overunity" has EVER been really achieved if it had then why are we not using them for power? most were "invented" in the 80's so thats about 20 years of RnD give or take

Yes you are quite correct but just think back in time. The computer would never work nor would the microwave oven even the jet never mind the Internet. Life as been full of debunked ideas but like most things it will get there and most likely a maverick will pave the way. Im finding out things that was drummed in at collage are wrong. How about you? Before you reply just have a ponder on it for a day or 2

For me right from the start of all my experimenting is for a self-running unit, so if Im not getting more power out than I putting in then unit is a complete failure for me. Im not in to charging batteries. But yes test results would be nice.

Thank you for the recovery and for your comments. A suggestion for everyone would be measure the charging power from your setup by swapping out the charging battery and running some tests with a large cap and a 'bleeding' resistor. Once you know your charging power, compare that with the amount of energy you put in the battery to get your charging effeciency. You would have to get Marthale7's famous CPU-heatsink battery tester software to measure the batt energy. It could be fun.

I will post on above when I have something worth explaining in depth but up to now I havent so I havent.
But may be I will consider doing so. Thanks for your comments and sorry for accidentally removing it.

Nice to see your motor-generator running. It looks like a nice flexible setup for performing all sorts of tests. Ultimately taking the testing to the next level is the key for all of the builders. Make real power-in power-out measurements, measure efficiencies, measure battery start/end output impedance, measure charging power, estimate and measure battery energy, do measurements on test vs. control setups, etc. I am not holding my breath for this to happen though.

Sorry it seems I have accidentally removed Drevtoobes comment. I intended to hit the reply tab but must of hit the remove tab instead. This was the comment left by Drevtoobe.

Good eplanation! BUT 75% right 25% wrong man :) and yeah,, could you please tone dwon your reply?

People who knows more, is eager and diggin for more, while people who knows less is eager to show what's his best.

You could be a guru for knowing such things "HOMIE", peace buddy. Let's take it easy, aight??? Life is short. hehehe!

HomeDistiller please tone down you replies some members are just starting out with all this.
But you explanation is good but now need for the dig. (Oh and if you had any idea of power generation you would know that cogging is) we all had to start somewhere even you. Again thanks for the explanation and your time in replying.

oh and if you had any idea of power generation you would know that cogging is the magnetic "stepping" effect that you get when you move the magnetic poles over the center of the coils, you can feel it is you turn a stepper motor (although in a alternator without iron you have no cogging effect so in this case it has no relevance as he has no iron in the alternator) a better design to use that has no cogging is an axial flux alternator

i know i cant do better because there is NO SUCH THING as "over-unity" it has never been shown to exists in any real experiments that can be reproduced by anyone. the Newman motor has been denied patents many times because it has been tested and DOESN'T WORK